Now slide the water line on to the water valve and connect the nut to the water valve until it's snug there will be another 1/4 nut and ferrell included with the water supply kit slide the nut and then the ferrell on the other end of the copper tube now connect this side of the copper water line to the water inlet valve located behind the refrigerator. If you're working from below, you can route the tube through ½-inch holes bored through the joists (above the mid-line) and drill a hole through the floor near the wall where the fridge will stand if you're tapping into the cold water supply to the faucet beneath the sink, you can bore holes through the base cabinet sides near the backs and route the tubing through them to the refrigerator. Rather than running a water line from under the kitchen sink through and behind drywall up through the ceiling into the attic then across and down in between the adjacent drywall and out the wall to the fridge’s water and ice dispenser seems like a lot of work. If you are lucky, there will be a hookup in your kitchen wall near the refrigerator if not, you will need to run a line to the nearest cold water pipe, which is probably in the floor below your. You need to find out a few things before you start your project, in this case we'll be using the lg refrigerator - other appliances may be similar, but you should double check the line hook-ups in the rear of your fridge.
Hooking your refrigerator to your water valve is a simple, do-it-yourself project requiring few materials and tools you'll need quarter-inch copper tubing that measures the length between your wall hookup and the hookup location on the back of your refrigerator, plus about 7 feet (to allow for moving the fridge. How to prevent water collecting inside your fridge by fixing your freezer drain the problem: refrigerators with defrosting coils, melt out the ice built up in the freezer by heating up and allowing the water to drip into the defrost drain. It is really a moot point even if you do connect the ice maker supply line to a hot water line, the hot water would never make it to the cube tray the volume of water inside the coiled length of one quarter inch tubing behind or under the refrigerator has been at room temperature for hours this water is often a sufficient volume to fill the tray. When hooking up a water line to a fridge ice maker or a door water supply, you want to use the correct materials to ensure the water flows well and everything is hooked up correctly with minimal chance of leaks.
If the kitchen sink is close to your frige, purchase a saddle valve and put on cold water line of incoming water to kitchen faucet you can use 1/4 plastic tubing or 1/4 copper either run through. Place the end of the water line you intend to connect to the refrigerator into a 5-gallon bucket turn the cold water supply valve on beneath the sink. The water line connection is at the bottom of the refrigerator on some versions of this model the threaded connection is likely covered with a protective plastic cover the image below shows how to connect the water line on the type of fitting that your model likely has. Note: if you already have an installed cold water valve behind your refrigerator, all you will need to hook up your fridge to water is some flexible plastic water tubing going from the wall valve to the fridge water inlet valve. If your old refrigerator had an icemaker and you are purchasing a new refrigerator, use the old tubing to connect it to the icemaker if it is still in good condition leave several feet of extra line so that you can move the refrigerator or the icemaker for cleaning.
When you are replacing an existing refrigerator that already has a water line hooked up, that makes your job a whole lot easier but when you don't have a supply line or pipe near by for your ice maker and water dispenser, it turns into a more detailed, lengthy and challenging process. 12 thread the nut on the tubing end onto the compression connector soldered to the cold-water supply line tighten the nut with pliers and an adjustable wrench 13 turn the water back on and test the water dispenser in the refrigerator door. Checked water and purposes it up the water lines tapping into a fridge water line to learn more about how to your fridge water supply over 40 million singles: we live in a water supply lines dishwashers.
What to the fridge, especially on the back of your ro system to hook to hook up water pipe can be hooked up a hole behind the ice maker water dispenser is a slab so you need to locate a will go. Step 5 – connect the water line to the valve wrap some thread-seal tape onto the threads of the piercing valve then, connect the water line to it tighten the nut with the adjustable wrench step 6 – pierce the water-supply line with the water line to the refrigerator connected to the piercing valve, turn the knob on the valve to pierce the copper tube this will puncture the water pipe you should hear the water starting to go through the water line. Your fridge is a water supply tubing, you hook up an extra 135 for a valve supplying the new refrigerator door refrigerator water line as we will need the toughest part of the copper water dispenser tube assembly on the. If you have a basement, tap into the cold water pipe down there doing so gives you easy access to the pipe and from the pipe to the floor area just behind the refrigerator if your home doesn’t have a basement, tap into the cold water supply line that goes to the faucet.
The copper tubing is used as a water line that you can connect to the water inlet valve located on the back of your refrigerator the water line must be properly connected if you want to use the ice maker in the freezer of your frigidaire refrigerator. If you don't have a convenient water supply pipe and valve near the refrigerator, you must instead find another spot to hook up the water line usually, this will be at some other existing water hookup point, like the water supply lines connected to your sink faucet or dishwasher. Best answer: you need to get the line kit for an ice maker, then you will have to perforate the cold water line to attach it you could add a small filter to the connection point for the ice maker. Flush one gallon of water (approximatlely 6 minutes) through the filter, by pressing the water dispenser lever, before drinking or using the water after you turn on the refrigerator, let the ice maker make ice for one or two days.